MOUNTING A TUB

Mounting A Tub

Mounting A Tub

Blog Article

Contact Us Today

What're your insights and beliefs on Tools You Need to Install a New Bathtub ?


How to Install a Bathtub Yourself
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a new one is also a reasonably hard job. If the old tub is readily obtainable, the task can move quickly; if you have to open up a wall to remove the old bathtub as well as position the new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the new one. Make sure you have actually qualified yourself for the work as well as fit trying it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a brand-new tub in your bathroom if you have currently gotten a brand-new tub and also don't require to alter the setup of your previous water system pipelines.
Your tools and also material list ought to consist of the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Setup


    To start with, the supporting framework supplied with the bath needs to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
    Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the supplied washers.
    Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.

    Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is frequently the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
    Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

    Setting up the Bathtub


    Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little points.
    The following goal is to make certain that the tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bath tub up until the level checks out level.
    To mount taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise check the overflow outlet and also the typical electrical outlet for leaks.
    Ultimately, fix the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used at the very least once as this will resolve it into its last placement.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipes.
    If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the area where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, resulting in complications with dampness and possible leaks to the ceiling below.
    You can select from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this activity prior to securing.
    Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I was made aware of that report on A Step-by-Step Guide to Installing a Bathtub from an acquaintance on another site. Liked our content? Please share it. Let others locate it. Thank you for taking the time to read it.




    Click


    Report this page